Laserfiche WebLink
SHEET A -6 - PARTITION SCHEDULE AND DETAILS <br />29. DETAIL 8/A -6 DETAIL OF NEW WINDOW SURROUNDS. Add the following note: "PROVIDE WOOD <br />SURROUNDS PER THIS DETAIL AT SILLS, JAMBS AND HEADS FOR EXTERIOR WINDOW AND DOOR <br />OPENINGS IN ROOMS 102, 104, 105 (EAST WINDOW ONLY), 109, AND 120 (WINDOW AND DOOR <br />OPENINGS.) <br />30. DETAIL 8/A -6 and 12/A -6 DETAIL OF NEW WINDOW SURROUNDS. Note that storefront system should be <br />center set instead of front set. <br />SHEET A -9 & A -10 - INTERIOR ELEVATIONS / BUILDING SECTIONS <br />31. In INTERIOR ELEVATION 3/A -9 and 31A -10, note that there Is no stained wood trim on the underside of the 8' -8" <br />high gypsum board soffit at Door 10313. All trim required is shown In the two elevations. <br />SHEET A -12 - CASEWORK <br />32. 2/A -12 AC -2A, 2B &2C. All notes indicating wall fabric WF -1 should include a reference to specification section <br /><09950 >. <br />33. 2/A -12 AC -2A, 213 &2C. Add the following note to the elevations of 2A and 2C: "PROVIDE RECESSED <br />STANDARDS WITH SHELF SUPPORTS ON ENDWALLS OF DISPLAYS FOR GLASS SHELVES." <br />STRUCTURAL <br />SHEET S -11 - GENERAL NOTES, PLAN, SECTIONS AND DETAILS <br />11S -1.1 EXISTING ROOF FRAMING PLAN <br />34. At the note for new openings which calls for "NEW 2X10 SYP No. 2 JOIST... ", change the number of face nails <br />from 0.131 "X3" at 12" oc. to "(2) 0.131 "X3" at 12" oc." <br />35. For the note describing installation of the missing x- bracing, change the note to read: "INSTALL NEW L3x3xi /4 X- <br />BRACING IN EXISTING BRIDGING LINES WHERE MISSING. BOLT ANGLES TOGETHER ATX- CROSSING w/3/4" DIA. <br />BOLT. ATTACH NEW BRACING TO NEW L3x3x1 /4x0' -4" CLIPS AT EACH END WITH 3/4" DIA. BOLTS. FIELD WELD <br />CLIPS TO EXISTING TRUSS CHORD w/ 3/16" FILLET WELDS. CARE SHALL BE TAKEN ATJOISTTOP CHORDS TO <br />PREVENT HEATING OF WOOD MEMBERS FROM WELDING." <br />36. Add the following note to the plan: "ATTACH JOISTS AT EXISTING AND NEW OPENINGS TO THE EXISTING <br />WOOD PLATE AT EACH END WITH (2) H2.5A ANCHORS BY SIMPSON,' <br />37. Add the following note to the plan: "The contractor shall add new 2X10 SYP No. 2 joists to each side of the <br />existing openings. These new joists shall bear on the bow string trusses at each and and be nailed to the <br />existing joists and each other with (2) 0.131 "X3" nails at 12" oc. <br />• Existing openings up to 4' -0" wide or up to 3 Interrupted joists: add one additional 2x10 <br />joists (2 total each side) <br />• Existing openings up to 5'-4" wide or up to 4 interrupted joists: add two additional 2x10 <br />joists (3 total each side) <br />38. Detail 21S -1.1. Add the following note: °3. FRAMES FOR NEW OPENINGS MAY BE FABRICATED IN THE <br />SHOP OR IN THE FIELD". <br />145 Union Street South ■ Concord, NC 28025 ■ Tel 704.788.2000 H Fax 704.788.2010 ■ www.ycharch.com <br />Attachment number 3 <br />G -3 Page 249 13 <br />